The tire is primarily held in place by its interference fit.

The shoulder on the outside and the retaining ring also keep the tire in place if the interference fit is lost.

This technique falls under the broader category of interference fits.

When warmed in place the resulting interference fit prevents motion.

Some can but need special equipment to insert the oversized bushing for an interference fit.

An Interference fit or friction fit requires some force to close and open, providing additional security.

Interference fit is generally divided as minimum and maximum interference.

Because the brake blocks apply directly on the tyre, it is heated up, relaxing the interference fit.

A shrink fit is an interference fit achieved by a relative size change after assembly.

No interference fit is used in any instance and the pin 'floats' entirely on bearing surfaces.

The interference fit renders the starter ring firmly attached to the flywheel.

Interference fit is obtained if the difference between the hole and shaft sizes is negative before assembly.

Rivets fill the hole where they are installed to establish a very tight fit (often called interference fit).

Removal of a worn tire is by machining out the retaining ring and heating the tire to relax the interference fit.

There are at least three different terms used to describe an interference fit created via force: press fit, friction fit, and hydraulic dilation.

Depending upon the actual limits of the hole or shaft sizes,fits may be classified as clearance fit,transition fit and interference fit.

Scoring of the wall of the hole and the absence of an interference fit left the inner lower boom vulnerable to developing fatigue cracks at Station 143.

An interference fit is generally achieved by shaping the two mating parts so that one or the other, or both, slightly deviate in size from the nominal dimension.

The inside diameter of the tire is machined to be slightly less than the diameter of the wheel centre on which it is mounted, to give an interference fit.

Typical examples of interference fits are the press fitting of shafts into bearings or bearings into their housings and the attachment of watertight connectors to cables.

For example, a shaft may be ground slightly oversize and the hole in the bearing (through which it is going to pass with an interference fit) may be ground slightly undersized.

The best fits are generally attained by selecting slightly oversized parts (or altering stock parts to form an interference fit) and then lapping the mating surfaces to attain the desired fit.

The engine block is mounted on a precision boring machine where the cylinder is then bored to a size much larger than normal and a new cast-iron sleeve can be inserted with an interference fit.

Formulas exist to compute this allowance (planned difference from nominal size) that will result in various strengths of fit such as loose fit, light interference fit, and interference fit.

Another is that a press fit should not be lubricated .

The retaining ring is made of steel and is a press fit.

A face without a drill point indicates that the dowel hole is a press fit.

Press fit is achieved with presses that can press the parts together with very large amounts of force.

Because of the "press fit" needed to hold the bearings, tighter, more precise machining tolerances are needed.

Toothed wheels fixed on the shaft are fitted by interference-for example, press or light press fit.

The headset cartridge bearings therefore sit somewhat loosely in the headtube of the bicycle (as opposed to being press fit).

An interference fit, also known as a press fit or friction fit, is a fastening between two parts which is achieved by friction after the parts are pushed together, rather than by any other means of fastening.

An Interference fit or friction fit requires some force to close and open, providing additional security.

Some have self-locking tabs, snaps, or have a friction fit.

Rollformed screen doors have mitered corners into which a steel or aluminum alloy corner is forced using a friction fit.

I sawed off the barrel of my Daisy and attached the .22 caliber barrel by friction fit.

Two types of porous coating used to form a friction fit are sintered beads or a foam metal design to mimic the trabeculae of cancellous bone.

"He's incredible; the part fit perfectly, and it's a friction fit and needs a perfect hole for the feed and nib to match, and he contoured it perfectly.

On the dial side the cannon pinion is attached with a friction fit (allowing it to slide when setting the hands) and the minute hand is attached to the cannon pinion.

Also, the loose friction fit of the edge connector on the already short interconnect cable created the precarious possibility of disconnecting the system bus from the CPU if either unit happened to be moved during operation.